Where is jumper-pin, boot-pin?

Discussion in 'Walkera Rodeo 110' started by guyver0324, Aug 16, 2019.

  1. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0

    Attached Files:

  2. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
  3. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    Thank you
    I already have an old version of cleanflight.
    I tried to connect but it didn't succeed.
    I investigated a lot. There is no problem with the USB driver.

    Are there any other possible problems?
     
  4. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    You need to power up drone and radio. Bind them then plug USB cable in.

    Cheers
     
  5. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    I have followed the procedure but cannot succeed.
    I tried both motor lock and motor unlock.
    Is there a problem with the USB connection?

    [​IMG]
     
  6. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    190818-01.jpg cp2102.jpg DSC_2552.JPG
     
  7. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    OK, Why are you trying to flash Cleanflight on the drone?

    And what makes you think the USB driver is OK?
     
  8. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    I want to adjust the motor.
    I would like to change the value of Minimum Throttle and calibrate ESC.
    I want to change the motor arm connection or change the buzzer switch setting.
     
  9. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    None of those functions are supported on the Flight Controller.

    Have you tried to flash firmware or settings before?
     
  10. guyver0324
    Offline

    guyver0324 New Member

    Joined:
    Aug 16, 2019
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    I set up another mini drone motor.

    If I want to adjust these features, do I have to replace it with a new power board?
     
Similar Threads
  1. Ian Pauli
    Replies:
    5
    Views:
    348
Loading...

Share This Page