walkera rodeo will not bind with devo 7 after i deed a reset on devo 7

Discussion in 'Walkera Rodeo 150' started by mario castagnoli, May 5, 2017.

  1. mario castagnoli
    Offline

    mario castagnoli New Member

    Joined:
    May 5, 2017
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    can anybody tell what to do for rebinding mi rodeo ,only one flight for 5 minutes.

     
  2. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,208
    Likes Received:
    318
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +415 / 13
    Why did you do the reset?

    Follow the programming instructions in the Quick start guide.
     
  3. mario castagnoli
    Offline

    mario castagnoli New Member

    Joined:
    May 5, 2017
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    because i am stupid and also that the drone wuold not torn off engine ,and thanks for the advice will let you know best rgards . Mario
     
  4. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,208
    Likes Received:
    318
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +415 / 13
    Most likely you accidentally pushed then throttle trim up. This is the reason I asked, so we could work out what might have gone wrong.

    Cheers brian
     
  5. FlyingKiller
    Offline

    FlyingKiller New Member

    Joined:
    Jan 11, 2018
    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Firenze
    Ratings:
    +0 / 0
    Hi all, (RODEO 150 mini fpv racing drone)
    Recently I received a Rodeo 150 as a gift from my parents. It was my first drone and I flied it for two/three times for training.
    After to read a lot of forum about Cleanflight I tried to use it but I wrongly change the calibration. After that the drone flied in a strage way and I wanted to reput the initial setting. Thinking to do a good thing, I pushed the switch on the CODE SWITCH POSITION window on the drone.

    Now I can't connect the drone with the DEVO7 controller
    What can I do???

    Cheers
    Emanuele
     
  6. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,208
    Likes Received:
    318
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +415 / 13
    You didn't read any of my posts on modifying your drones. Its a don't.

    And I advise against it. Config modifications are n ot supported. But people continue to fiddle and destroy their drones.

    You have bricked your FC.

    Search our forums and you will find out how to short some pins and get the FC to boot from rom. Also you can only use cleanflight version 1.2.0 .

    Only use this version of Cleanflight.

    SW:CleanFlight version 1.2.0 F210, F150, F110 Compatible English

    If you get the current cleanflight from the chrome store it will brick your drone.
     
    • Like Like x 1
  7. FlyingKiller
    Offline

    FlyingKiller New Member

    Joined:
    Jan 11, 2018
    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Firenze
    Ratings:
    +0 / 0
    Hi @bjr981s thank you for your aid to me.

    I downloaded the 1.2.0 CF version from your link and I connected my drone with it.
    What I have to do then to reput the start setting on my drone?
    Do I have to use the "Rodeo 150 Cleanflight fireware" provided by the official site of walkera?

    Cheers
     
  8. FlyingKiller
    Offline

    FlyingKiller New Member

    Joined:
    Jan 11, 2018
    Messages:
    5
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Firenze
    Ratings:
    +0 / 0
    Hi @bjr981s I install the correct CF version as you said to me, I connected my rodeo 150 and I reset the configuration using the walkera rodeo 150 configuration from the official site.

    Now my drone run!!! Really thank you for your help!!

    cheers
     
  9. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,208
    Likes Received:
    318
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +415 / 13
    Thats fantastic. Happy flying.

    Cheers
     

Share This Page