Need X350 Pro and Devo F12E Device output settings

Discussion in 'Walkera QRX350/QRX 350 Pro/QRX 350 Premium' started by Kristjan, Jul 3, 2017.

  1. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    I just got X350 Pro and Devo F12E separately. I have been reading the manuals but there is absolutely no information on what the Device output settings are supposed to be to match the F12E switches to the X350 and the Gimbal and the iLook camera. I must say that the Walkera manuals are next to completely useless with no usable information what so ever.

    Does anybody have the correct Device output settings?

     
  2. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,273
    Likes Received:
    329
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +429 / 13
    Its clearly explained in the X350 user manual. Pages 11 to 16.

    The additional channel settings for 12 channels are on page 16. Its uses the 12S as the example. This is because the F12E did not exist at the time of the X350 lifecycle.

    Cheers

    Gt the manual from here it is to large for me to attach.

    Walkera QR X350 PRO User Manual | First Quadcopter

    I must disagree with your comments, this manual is extremely detailed. I'm not sure what your expectations are:?
     
  3. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    Well the included manual didn't have any section for 12S. I tried to find the manual on Walkera site, but it seems that absolutely every documentation related to X350 Pro is completely gone from Walkera, which is not really helping. At least the version you linked to does include 12S.

    It seems there is some mismatch of information. In my manual it says Gimble Tilt is on AUX1. Your manual says that Gimble Tilt is on AUX4. On my X350 I can see that the actual wire goes to AUX1. There seems to be so many different versions of X350 Pro with different receivers: RX703, RX703A, RX705 which makes finding any relevant information on the web difficult.

    But I think I have managed to get everything mapped correctly now.
     
    • Like Like x 1
  4. eamon honda
    Offline

    eamon honda New Member

    Joined:
    May 29, 2018
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    hi i am also looking for devo f12e output setting can you help
     
  5. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    Yes the thing is that there are two version of the QR-X350 one is with the RX703A receiver and the newer version is with the RX705 receiver. If you look into the battery compartment you can see which version you have. If you have the RX705 receiver the device output is as following:

    Gear=Mix SW
    Flap=Rudd D/R
    AUX2=Elev D/R
    AUX3=FMod SW
    AUX4=(Free channel not used)
    AUX5=AUX5 (Gimbal Roll)
    AUX6=AUX6 (Gimbal Tilt)
    AUX7=AILE D/R
     
  6. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    The device output settings really depend on what version of X350 you have and what Camera and Gimbal are attached. If you post what you have and what you want to do I can help more.
     

Share This Page