need help!! trouble locking the motor

Discussion in 'Walkera Aibao' started by ady permana, Jan 24, 2017.

  1. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    hi guys,
    i bought walkera aibao two days ago and i need help. today i fly the aibao indoor and use manual mode theres no problem drone flying smooth from took off. but the problem comes when i try to lock/disarm the motor after the drone landing on the ground. first i try method 1 from the manual push and hold the throttle stick down for more than 5 seconds but nothing happen the motor still unlocking so then i try the method 2 from the manual that is move the left and the right stick while outward and hold but suddenly the motor spinning wildly and the drone jump backward about 2 meters and smash into the wall and break two propeller . what happen?..why the both method doesnt works correctly!? can you exsplain to me? im i do something wrong? is this some kind of walkera aibao failure?..i already fly some drone before i bought aibao and they all have same method to lock or disarm the motor and the all work just fine. this is the first time i got problem with locking or disarm the motor. please give me solution how to lock or disarm the motor savely on manual landing.thanks

     
  2. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,320
    Likes Received:
    334
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +436 / 14
    Did you have trim set.

    try calibration you controller.
     
  3. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    not yet .ok ill try that later. thanks bjr981s
     
  4. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    hi bjr981s. now ihave new problem. when i turn on the drone i cant arm the motor. the blue light and the red light flash alternately. have any idea?
     
  5. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,320
    Likes Received:
    334
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +436 / 14
    Wait. It takes a long time to warm up.
     
  6. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    when i turn on the radio and then the quad its ussualy only take a minute to stabilize the light but now i already wait for 10minute and the quad light still flashing alternately red and blue it wont stop and icant even unlock the motor
     
  7. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,320
    Likes Received:
    334
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +436 / 14
    Did you calibrate the controller or the Aibao?
     
  8. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    i try to caliberate the controler but fail. i try some combination after enter caliberation setup by press the gimbal return button and then after light flash alternately i move the both stick all direction and then press and hold the gimbal button again but it fail..the controler vibrate...in manual only writen "operate the stick several times within mechanical tuning range and then back in the middle " i dont understand so i look on yutube but only have devo 7 caliberation method and i try the same method but fail. how to do stick caliberation correctly?
     
  9. ady permana
    Offline

    ady permana New Member

    Joined:
    Jan 23, 2017
    Messages:
    19
    Likes Received:
    1
    Trophy Points:
    3
    Ratings:
    +1 / 0
    i did the compas caliberation too and its succesfull...the four light on the quad both bright just likes on the manual say but then about 3 second the red light and the blue light flashing alternately again and it wont stop
     
  10. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    5,320
    Likes Received:
    334
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +436 / 14
    You will not be able to do anything until you calibrate the TX correctly.
     

Share This Page

Search tags for this page
walkera aibao stick calibration
,

waterboyy the series yutub