Is somebody using QR X350 Premium ?

Discussion in 'Walkera Talk' started by Drist56, Jun 4, 2015.

  1. Drist56
    Offline

    Drist56 New Member

    Joined:
    May 18, 2015
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    I have some problems on using GCS software with my qr x350 Premium. I posted a video showing this problem in the 'walkera help' section of this forum.
    Since walkera put a new version of GCS on its website (version from end May), bluetooh connection works well.
    But the Code Binding still not carried out. The red LED continues to flash quickly. Is someone uses the GCS with the premium?
     
  2. bjr981s
    Online

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    3,318
    Likes Received:
    208
    Trophy Points:
    63
    Location:
    Sydney, Australia
    Ratings:
    +268 / 9
    I have a Premium and have done a quick attempt to bind the BT. I did not get it to go.

    I did notice that the Premium does not have its test lights activated (the lights above the battery compartment) until the F12E binds with the model.

    Try binding the BT after the F12E binds. There is instructions in the manual on how to swap from BT to F12E and back again.

    I have my premium packed away at the moment and I am flying my Tali H500 and doing a gimbal update to the 3DH. Also modding a Scout x4 to an X8

    When I get the premium out again I will try and do a BT bind.

    Cheers
     
  3. Blisk
    Offline

    Blisk New Member

    Joined:
    Sep 9, 2015
    Messages:
    19
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    I tried to bind after F12E connects to qr x350 p. but CGS software crshes imediatelly.
     
  4. pdule
    Offline

    pdule Member

    Joined:
    Jun 14, 2016
    Messages:
    48
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0 / 0
    I bought a new Walker premium RTF (FPV-iLook, ..). When I turned on the Walker started flashing red light and not fade over.
    What should I do ?.
    Thanks for the help
     
  5. bjr981s
    Online

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    3,318
    Likes Received:
    208
    Trophy Points:
    63
    Location:
    Sydney, Australia
    Ratings:
    +268 / 9
    Can you be a bit more explicit?

    Have you followed the quick start guide?

    Did you power on the TX and immidelty power on the Premium?
     
  6. pdule
    Offline

    pdule Member

    Joined:
    Jun 14, 2016
    Messages:
    48
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0 / 0

    ReŇ°ilsem problem. The first is the need to turn Drona then radio.
    Now I have a new problem. Batteries dronu can not turn off with a switch. When the switch is ON, all operating normally, but when jestikalo OFF everything works the same way except that the red light is switched off. Can you help me.
     
  7. pdule
    Offline

    pdule Member

    Joined:
    Jun 14, 2016
    Messages:
    48
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0 / 0


    I solved the problem. The first is the need to turn Drona then radio.
    Now I have a new problem. Batteries dronu can not turn off with a switch. When the switch is ON, all operating normally, but when jestikalo OFF everything works the same way except that the red light is switched off. Can you help me.
     
  8. bjr981s
    Online

    bjr981s Moderator Staff Member

    Top Poster Of Month

    Joined:
    Sep 19, 2015
    Messages:
    3,318
    Likes Received:
    208
    Trophy Points:
    63
    Location:
    Sydney, Australia
    Ratings:
    +268 / 9
    You are too slow in turning on the battery. You only have 5 seconds to do it.

    First. Turn on the switch on the battery. There will be no bright red light.
    Second turn on the TX.
    Third. Press the on button on the battery and hold till the battery starts.

    Cheers
     
  9. pdule
    Offline

    pdule Member

    Joined:
    Jun 14, 2016
    Messages:
    48
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0 / 0
     
  10. pdule
    Offline

    pdule Member

    Joined:
    Jun 14, 2016
    Messages:
    48
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0 / 0
    Thanks!
    I solved the problem. The first is the need to turn Drona then radio.
    Now I have a new problem. Batteries dronu can not turn off with a switch. When the switch is ON, all operating normally, but when jestikalo OFF everything works the same way except that the red light is switched off. Can you help me.
     

Share This Page

Search tags for this page

how to use gcs for qr x350 premium

,

problem with walkera x350 premium

,

walkera premium 350 problems

,

walkera qr x350 premium problems