f210 3D fault

Discussion in 'Walkera F210' started by Frederico Freitas, Sep 10, 2019.

  1. Frederico Freitas
    Offline

    Frederico Freitas New Member

    Joined:
    Sep 10, 2019
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    Good afternoon, a friend bought a walkera f210 3d, at the time of calling said he did not know how to do. and was unsuccessful in connecting, tried to update on cleanflight but I don't know what procedures it did. As I don't have much experience, I decided to ask for help. well come on. When the drone is turned on, only the front led will light up and beep.

     
  2. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    If you connected to cleanflight you most likely bricked the FC.

    Was the purchase a RTF drone and Transmitter or bought separately?
    What version of Cleanflight did you connect with?

    Please advise and we can progress.
     
  3. Frederico Freitas
    Offline

    Frederico Freitas New Member

    Joined:
    Sep 10, 2019
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    Not yet, I researched and downloaded 1.2.4 I did not get to connect, but I think previously between was connected do not know the version, everything was bought together, the control drone and vr glasses.
     
  4. Frederico Freitas
    Offline

    Frederico Freitas New Member

    Joined:
    Sep 10, 2019
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    At the time of turning on the procedure was incorrect, I do not know if it influences, but after that apparently did not work the tutorial tutorial.
    How do I find out if the FC is brick?
     
  5. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    Download Cleanflight from our Resources TAB. You need the version 1.2.0

    SW:CleanFlight version 1.2.0 F210, F150, F110 Compatible English

    Ensure that you have the correct device drivers installed.

    Use Cleanflight 1.2.0 to connect to the drone. Make sure that it is powered on with the battery before connecting it to the PC USB port.

    If it connects OK then use the FW update from our Resources TAB

    FW:F210 3D Original Manufacture FW and Settings

    Ensure that you follow the instructions included in the Download.

    Let us know what happens.

    Cheers Brian
     
  6. Frederico Freitas
    Offline

    Frederico Freitas New Member

    Joined:
    Sep 10, 2019
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Ratings:
    +0 / 0
    upload_2019-9-26_13-26-41.png
    not going is giving error.
    I performed the following process. I installed the correct version as in the tutorial. I restarted the PC. I put the drone without battery in the cable and turned on the pc, after that I tried to connect.
    Best regards Frederico Freitas
     

    Attached Files:

  7. bjr981s
    Offline

    bjr981s Moderator Staff Member

    Joined:
    Sep 19, 2015
    Messages:
    5,819
    Likes Received:
    438
    Trophy Points:
    83
    Location:
    Sydney, Australia
    Ratings:
    +553 / 16
    Try and reinstall the FW again. This time ensure that you do it with full chip erase.

    Make sure you do it with local FW update and do not select a board FW.

    Make sure you don't go past the first FW update screen.

    Let me know what happens.
     

Share This Page