Connecting "Start video" switch to iLook+

Discussion in 'Walkera QRX350/QRX 350 Pro/QRX 350 Premium' started by Kristjan, Jul 8, 2017.

  1. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    OK I have the Devo F12E and G-2D gimbal and iLook+. Everything is connected correctly, I can pitch and roll the camera fine but I want to connect the "Start video" switch on the F12E to start recording on the iLook. It looks to me like the wire that is supposed to connect from the powe wire to the RX703A is missing? The instructions say to connect the "Camera controller" wire but there is no such wire in either the G-2D gimbal package or the iLook package. So do I have to specially buy that wire?

     
  2. conner
    Offline

    conner Member

    Joined:
    Aug 28, 2016
    Messages:
    33
    Likes Received:
    3
    Trophy Points:
    8
    Location:
    virginia, usa
    Ratings:
    +3 / 0
    yes you need a wire, its in a kit, the walkera camera cable pack.
     

    Attached Files:

  3. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    I have all of these cables. None of them can connect to the TX703A three pin input. But I think this is the pack that I need "Walkera FPV Spare Parts 5.8 G Image Transmission"? The cable with the tree pin and two pin.
     

    Attached Files:

  4. conner
    Offline

    conner Member

    Joined:
    Aug 28, 2016
    Messages:
    33
    Likes Received:
    3
    Trophy Points:
    8
    Location:
    virginia, usa
    Ratings:
    +3 / 0
    the "camera transfer wire" in the kit will plug into your wire. in your photo, it is the one on top. the one you need is lower right in my photo.
     
  5. Kristjan
    Offline

    Kristjan New Member

    Joined:
    May 9, 2017
    Messages:
    25
    Likes Received:
    1
    Trophy Points:
    3
    Location:
    Iceland
    Ratings:
    +1 / 0
    OK so I will have to get this extra wire for the camera control switch. Strange the iLook package doesn't include this wire.
     
  6. conner
    Offline

    conner Member

    Joined:
    Aug 28, 2016
    Messages:
    33
    Likes Received:
    3
    Trophy Points:
    8
    Location:
    virginia, usa
    Ratings:
    +3 / 0
    yes typical walkera, terrible / no instructions. hook camera control wire to aux 1 and use gear switch to operate, normally up, then flip down and back up about 1 second, to turn video on and off. or take a photo with each flick of switch.
    be careful on radio setup, if not set up properly you may be in IOC at take off, and not realize it
     
  7. conner
    Offline

    conner Member

    Joined:
    Aug 28, 2016
    Messages:
    33
    Likes Received:
    3
    Trophy Points:
    8
    Location:
    virginia, usa
    Ratings:
    +3 / 0
    since you have a F12 I think AUX4 can be used for gimble pitch
     
    • Like Like x 1

Share This Page

Search tags for this page

devo f12e and ilook camera on off control problem

,
gimbal g-2d devo f12e start recording